Identificador: 2458
Abierta
ID de articulo : # 2458 se ha agregado a su lista de deseos.
Descripción
PARTE: 12572 - PRENSA DE RADIO FRECUENCIA - OGDEN
USADA - BUENAS CONDICIONES
Curing area: 36” x 60” x 2” thick.
Clamping pressure is applied by multi-power (dual pistons on a common shaft) pneumatic cylinders to maximize pressure while relying on standard plant pressures. Unlike presses without multi-power cylinders, which require booster compressors, the Model SL36x60 reaches full capacity at 100-psi plant air pressure.
Edge pressure is applied by eight (8) each pusher shoes, each with a 4” bore x 4” stroke twin-piston multi-power pneumatic cylinders.
Top platen pressure is applied by two (2) 5” diameter x 16” stroke pneumatic cylinders through a cantilever arm that keeps the footprint to a minimum while still allowing the operator full access to the platen area.
The platen is set at a 45-degree angle and the top platen opens wide; allowing the operator to step inside the press for ergonomic and accurate parts placement.
The internal solid state RfsProtech 6KW Generator cures approximately 600 square inches of glue line per minute.
The Generator features solid state rectifiers and all aluminum cabinet for maximum conductivity and superior performance.
Two-hand no-tie-down safety controls for closing the top platen.
Controls are simple to understand, and are complete with the required push-buttons, switch, meters, digital operator display, and on-screen troubleshooting diagnostics.
The machine is controlled by a PLC for dependability and efficient maintenance. All controls will be provided for safe and efficient operation. The operator screen permits efficient operation, and the included press diagnostics screens assist in trouble-shooting when the need arises.
Proper interfaces will be provided for operational signals and emergency system stop.
All necessary RF controls, including buttons, meters, and PLC operator interface panel are mounted on a control panel attached to the left front of the press.
Interlocked top platen and safety switches on all access doors insure operator safety.
Power requirements are 480 volt, 60 cycle, 3 phase electric.
Circuit breaker protection is provided. A service disconnect is required for safety, but is not provided.
Powered In-Feed table with motor and controls
Out-feed steel deck
Voltage 480 volts 60 Hz
Pago y Devoluciones
- Forma de pago
- Transferencia/Deposito Bancario
Publicar mensaje
Ingresar to ask the seller a question.
AMXmachinery
SIERRA CINTA 10"
PARTE # SIL-DC-SC10-B - SIERRA CINTA DE 10" - MOTOR 1/2 HP NUEVA CON GARANTIAMOTOR: 1/2 HP, 110V, 60 Hz, 1 FASEDISTANCIA DE CINTA A COLUMNA: 230 MMALTURA MAXIMA DE CORTE: 80 MMTAMANO DE LA MESA: 290 X 290 MMINCLINACION DE LA MESA: 0 - 45 GRADOSLONGITUD DE LA SIERRA CINTA: 1511 MMANCHO DE LA SIERRA CINTA: 9.8 MMPESO: 16 KGSEMPAQUE: 1 CAJA
AMXmachinery
HORNO PARA CERAMICA, VIDRIO, METALES – 299 LITROS
PARTE:
2PG-TNF283 – HORNO PARA CERAMICA, VIDRIO, METALES – 299 LITROSNuevo con garantiaThe massive, 12-sided digital TnF-28-3 is a profit center of the busy ceramic studio. It eats up stacks of low-fire ware. At a cost per cubic foot, the TnF-28-3 is one of the most economically priced standard kilns we make.The TnF-28-3 now features sectional construction. Separate the kiln bottom and sections to repair bricks, change elements, or to move the kiln down narrow stairwells or through the narr...
AMXmachinery
PARTE: 12533 - ESCOPLO OSCILANTE - 2 MESAS - BALESTRINI
PARTE: 12533 - ESCOPLO OSCILANTE -
2 MESAS - BALESTRINI
USADO - MUY BUENAS CONDICIONESModelo MicronMax
oscillation length: 120mm (4.8")Max
slot depth: 80mm (3.2")Max
slot thickness: 30mm (1.2")Hourly
production: 500-800 slotsSpindle
rotation: 9,000 RPMOscillations
per min.: 60-350Max
table inclination: 20 degreesTables
19" x 9"Pneumatic
holddown on each tableSpindle
motor: 3HPOscillation
motor: 1/2HP
Current
Voltage: 220v
AMXmachinery
ENLAZADORA/COLA DE MILANO
PARTE # 2CA-JDT65 - ENLAZADORA/COLA DE MILANOIdeal for drawer production and furniture parts which require high quality dovetail joints.Max. workpiece size 59" x 16 ½"Workpieces are clamped by air clamps.Enclosed-type stand.Equipped with an indication bar for indicating cutting position.Tenon width can be micro-metrically adjusted in 2 mm.Tenon and mortise depth are conveniently adjusted according to the thickness of workpiece.Equipped with one four-sided template providing four types of pitche...