Identificador: 1248
Abierta
Descripción
PARTE # RT-R113 – TALADRO MULTIPLE - 13 TALADROS – VERTICAL – MANUAL
Nueva con garantía
Fotos y Características:
3/4 HP Spindle Drive Motor, TEFC
60″ Back Fence Assembly
(1) 13-Vertical Gear Driven Spindle Rows
10mm Bored Collets
(7) Right Hand, (6) Left Hand
(2) Index Pins
20″ X 48″ Work Table Surface
Wired 1-Phase 120 Volt, 60 Hz.
Manually Actuated Boring Cycle
Tooling Not Included
Crated Dimensions: 45″ X 80″ X 44″ and 508 Lbs
Designed and Manufactured in the USA
The starting point for our line boring machines, this unit is both affordable and built to last. No more using templates that wear out quickly and lose accuracy. This machine is easily adjustable for entry and exit points, and cleanly allows the user to repeat the drill hole pattern with centering pins on both the left and right hand side of the machine. The rear fence is adjustable for offset from the edge as well. If you’re looking for your first line bore drill, look no further. This machine will give you many years of service with little to no maintenance. This is a clear choice among professionals.
Pago y Devoluciones
- Forma de pago
- Visa/Mastercard/American Express
Publicar mensaje
Ingresar to ask the seller a question.
AMXmachinery
ENCHAPADORA - CEHISA - PRO 8
PARTE: 12262 - ENCHAPADORA - CEHISA -
PRO 8
USADA - MUY BUENAS CONDICIONES
220V, 3 FASES, 60 HZ
TOTAL HP 7.58
SINGLE LARGEST HP 5.58
TOTAL AMPS 17.2
GLUE TANK: M-5
STATIONS:
- END TRIMMING
- TRIMMING
- POLISHING
AMXmachinery
PARTE: 1AM-3011 – MESA DE RODILLOS – ENTRADA Y SALIDA MAQUINAS – 120 CM LARGO – CON TOPE Y GUIA
PARTE: 1AM-3011 – MESA DE RODILLOS
– ENTRADA Y SALIDA MAQUINAS – 120 CM LARGO – CON TOPE Y GUIA
MESAS LATERALES
PARA SIERRAS TRONZADORAS,
CORTADORES RAPIDOS, SIERRAS PENDULO, ETC.
PARA ENTRADA Y SALIDA DE PIEZAS
LARGAS Y/O PESADAS EN MAQUINAS
CON GUIA Y TOPE AJUSTABLE PARA
HACER CORTES A MEDIDA
NUEVA CON GARANTIA
120 CM LARGO X 39 CM ANCHO
ALTURA VARIABLE 83 CM – 87 CM
7 RODILLOS CON BALERO
- GUIA PARA EL MATERIAL EN LA PARTE
TRASERA
- 1 TOPE AJUSTAB...
AMXmachinery
PARTE: 2TA-BS-1212HR-TN - REASERRADORA HORIZONTAL - 2 SIERRAS
PARTE: 2TA-BS-1212HR-TN - REASERRADORA HORIZONTAL - 2 SIERRASPARTE: 2TA-BS-1616HR-TN - REASERRADORA HORIZONTAL - 2 SIERRASNUEVA CON GARANTIASpecificationsBS-1212HR-TNBS-1616HR-TNMax. Cutting Capacity12" x 12"16" x 16"Distance between Blade to Conveyor1/4" ~ 12"Saw Wheel Diameter28" x 2Saw Blade Length (Width)201" (2")201" (2" ~ 3")Saw Blade Speed6000 FPMFeed Conveyor Width12"16"Feed Speed (Variable)0 ~ 90 FPMMain Motor (Each Head)20 HP x 230 HP x 2Saw Blade Lift Motor1/2 HPFeed Conveyor Motor3 H...
AMXmachinery
PARTE: 12596 - TRITURADORA - BLOAPCO - MODELO 7-6
PARTE: 12596 - TRITURADORA - BLOAPCO - MODELO 7-6USADO – BUENAS CONDICIONES - RECONSTRUIDOMax trim width 7.5"Shear Cutting ActionRotor Speed 500 to 3,600 RPMModel 7-6 provides cutting via one stationary bed knife and two rotating knives provides two cuts per revolution. The open-rotor design facilitates free passage of air and material. Shear-cut action for paper and tough, thin film and foil.Total weight is 135 pounds17"L x 13.25W x 22.5H