ID: 1729
Open
Description
PARTE: 2CK-JEN60
Designed to both notch and drill drawer boxes to install undermount soft-close drawer slides. The operation of the machine is simple with a self-indexing drilling unit that’s determined by the position of the drawer for either left or right notching. With a cycle time of approximately 10 seconds per drawer, you can achieve a high throughput and save time for other important tasks.
- High production capacity of up to 220 drawers machined per hour.
- 57mm (2 ¼”) wide cutter head allows you to machine notches for a wide range of undermount drawer slides without needing to change heads or machine the component twice.
- Self-indexing drill unit for left or right drawer notching.
- Convenient foot pedal operation lets operator efficiently load and unload drawers for higher output.
KEY ADVANTAGES
- Pneumatic cutter & drill stroke by foot pedal operation.
- Cutter stroke and drill speed are adjustable for optimum finish results
- Drill will automatically position for both left and right drawer notches by activating a switch in the fence
- Machine will not cycle unless a drawer is up against the switch for safe operation
- Insert knife cutterhead with solid carbide inserts for optimum finish results and long tool life
- 2 ¼” (57mm) wide cutter allows for a wide range of undermount slides
- Comes with insert cutterhead with inserts and ¼” (6.3mm) solid carbide drill bit.
- Capable of notching up to 220 drawer boxes (both left and right) per hour.
|
Main cutter motor |
3 HP |
|
Notch dimensions |
2 ¼” (57mm) x 0.5” high |
|
Cutter diameter |
10” |
|
Drill diameter |
¼” |
|
Table size |
49” x 22” |
|
Table height from floor |
32” |
|
Dust port |
4” (670 CFM requirement) |
|
Compressed air required |
90 – 100 PSI |
|
Machine dimensions |
48” x 37 ¾” x 39 ¾” |
|
Machine weight |
506 lbs. |
Payments & Returns
- Payment Methods
- Visa/Mastercard/American Express
Post Message
Sign in to ask the seller a question.
AMXmachinery1
CORTADORA DE METAL HIDRAULICA 4' x 10 Ga
CORTADORA DE METAL HIDRAULICA 4' x 10 Ga PARTE: 2GM-HS-0410MDTaiwan machinesISO 9001 certifiedHD all steel construction for maximum rigidityGerman logic quiet Rexroth hydraulic systemAdjustable stroke from 16-20 strokes per minute60” long squaring arm with inch / mm scaleSpring hold-downs High grade carbon/chrome alloy steel blades and hardened to 62 HRC, 2-edge indexable upper blade and 2-edge indexable bottom bladeFull length with full view finger ...
AMXmachinery1
CANTEADORA AUTOMATICA
CANTEADORA AUTOMATICA PARTE: 2CK-MX340Is a compact edgebander capable of applying up to 3mm thick edge tape on cabinet parts and more. It comes equipped with high frequency motors on both the end trim and top & bottom trim. In addition it is equipped with PVC radius scraping and buffing units. It’s compact design and affordable price point make it the ideal edge banding solution for the small cabinet shop who does not require pre-milling.Versatile edgebander capable of applying...
AMXmachinery1
SIERRA MULTIPLE - 1 SIERRA - 14 PULGADAS
PARTE: 2CK-SRS330Is a single-blade ripsaw is geared towards the shop looking to increase efficiency in their ripping operations but cannot justify a multi-blade ripsaw. With its precision cast iron chain and track assembly, and extended pressure section, the SRS330 can produce a glue joint finish ready for panel glue-up right out of the saw.Produces a guaranteed glue joint finish to 13′, which eliminates the need to joint the material after rippingPrecision straight line feeding for parallel...
AMXmachinery1
FRENO PARA DOBLADORA DE METAL
FRENO PARA DOBLADORA DE METAL PARYE: 2GM-SB-1014ISO 9002 certifiedLarge 3” beam opening, adjustable1” beam adjustment (front and back)Stop rods for repeat bends(2) counter weightsAll steel heavy body construction with extra heavy tie rod for minimum deflectionBending Capacity: Mild Steel14 Ga.Bending Capacity: Stainless Steel18 Ga.Bending Length Capacity10'Bending Angle Degree0-135°Beam adjustment, front and back1"Minimum reverse bend5/16"Manual clampingSt...