PARTE: 2PG-F-130 – HORNO PARA CERAMICA, VIDRIO, METALES – 25 LITROS

PARTE: 2PG-F-130 – HORNO PARA CERAMICA, VIDRIO, METALES – 25 LITROS

Nuevo con garantía

Temperatura Máxima: 926 grados centígrados

2400 watts, 20 Amps

Medidas interiores: 279 mm ancho x 279 mm fondo x 330 mm alto

 

You can make figurines up to 12” tall in the F-130. Anneal large glass beads and marbles. Raise the spring-loaded vertical-drop door to insert a glass figurine with a punty rod. Lower the door. The punty rod will extend outside the firing chamber through the smaller 4” x 8” punty rod door. This allows even large glass pieces to anneal safely.

 

Enjoy the glittering beauty of dichroic glass. This kiln will give you a haven of creative enjoyment that will immerse you for many years. Imagine how it could change your life style.

 

Thick firebricks; sidewall element

The firebricks in the roof, walls, door, and bottom are 3” thick. This is 20% more insulation than the standard 2 1/2” firebricks in the walls and bottom of our earlier F-130 kilns. The extra insulation enables the F-130 to maintain a temperature hold with greater ease. Sidewall heat is now standard in the F-130. The element heats from the sides and back of the kiln in dropped, recessed wall grooves.

 

Deluxe door gaskets

Because of a gap under the small punty rod door, you can usually close the door all the way even when mandrels extend past the firing chamber. This helps to retain the heat in the kiln. Powerful, rare-earth magnets hold the punty rod door in the open and closed positions. To further retain heat, the 4” x 8” punty rod door is 2” thick and includes two woven, flexible high-temperature gaskets.

 

Slide-out mandrel holder

The mandrel holder can be adjusted horizontally and vertically without tools. Position the heavy-duty welded mandrel holder anywhere from 4 1/2” to 13” in front of the main section of kiln floor. (Note: The firebrick extension on the front of the kiln extends 3” beyond the front edge of the kiln floor.) Then tighten the mandrel holder with thumb screws. The holder slides inside steel tubes in the base of the kiln. The stainless steel mandrel rest, which includes 7 slots, can be adjusted vertically.

 

Sloped control panel

The control panel is angled for easy viewing and operation of the digital controller. Program the kiln from a comfortable position. The controller, pilot light, and switch are mounted on a brushed stainless steel plate. Gain easy access to the electrical components by removing the front panel.

 

Stainless steel rod warmer

To save production time, pre-heat glass rods on top of the kiln. The 5” long stainless steel rod warmer is slotted for five rods.

 

Tested by TUV

And for your safety, the F-130 is tested by TUV, Germany’s leading testing lab, to meet UL and CSA standards. The kiln includes an on/off switch for your convenience.

 

Basic kiln features

On/off switch; easily reboot the controller.

Safety pilot light

Dropped, recessed sidewall element grooves

3” insulating refractory firebricks in the roof, walls and bottom

Electrical components stay cool in a slotted base.

Precisely balanced spring-loaded vertical-drop door

Double gaskets under the 2" thick, 4” x 8” punty rod door

Rare earth magnets hold the punty rod door open or closed.

Stainless steel sheet metal screws

TUV tested to UL and CSA standards.

Made in the USA

Thermocouple with “special limit” wire

The thermocouple senses temperature inside the kiln. It is the small rod that extends into the firing chamber. The ¼” wide Type-K, 14-gauge, exposed-tip thermocouple is made with special-limit wire for superior accuracy. The exposed tip gives the controller a fast response time for even temperatures during holds. The thermocouple is made in America to our exacting standards.

Designed for production

Paragon’s warranty is not affected by frequency of use. Fire your new kiln every day if you want, even in commercial settings. That will have no effect on the warranty period.

Recommended furniture kit for the Paragon F-120, F-130, and equivalent sized kilns.

Included:

1 – C-10S Shelf (10” square x 1/2”)

4 – 1/2” long, 1” wide Square Posts

 

Max. Temperature: 1700F - 926C

Amps: 20

Phase: 1

Watts: 2400

Nema: 5-20R

TUV tested to CSA and UL Standard 499: Y

CE: N

IMPORTANT: Some areas such as Canada and Europe require a lid or door safety switch on kilns.

Control Type: Sentry Xpress 4.0 Digital 3-Key

Voltage: 120

Hertz: 60

Kiln Type: Front Loading Square

Sides: 4

 

Chamber Volume: 0.90 CU.FT. = 25.49 litres

Chamber Width: 11.00 IN = 279 mm

Chamber Depth: 11.00 IN = 279 mm

Chamber Height: 13.00 IN = 330 mm

 

The Outer Size of the Kiln and the Shipping Size: Width = Left to Right; Depth = Front to Back; Height = Top to Bottom

 

Outer Size:

22.00W x 26.00D x 28.75H Inches

559W x 660D x 730H mm

 

Ship Size:

32.00W x 34.00D x 39.00H Inches

813W x 864D x 991H mm

 

Ship Weight:

220.00 Lbs.

99.79 Kg.