Identificador: 2458
Abierta
Descripción
PARTE: 12572 - PRENSA DE RADIO FRECUENCIA - OGDEN
USADA - BUENAS CONDICIONES
Curing area: 36” x 60” x 2” thick.
Clamping pressure is applied by multi-power (dual pistons on a common shaft) pneumatic cylinders to maximize pressure while relying on standard plant pressures. Unlike presses without multi-power cylinders, which require booster compressors, the Model SL36x60 reaches full capacity at 100-psi plant air pressure.
Edge pressure is applied by eight (8) each pusher shoes, each with a 4” bore x 4” stroke twin-piston multi-power pneumatic cylinders.
Top platen pressure is applied by two (2) 5” diameter x 16” stroke pneumatic cylinders through a cantilever arm that keeps the footprint to a minimum while still allowing the operator full access to the platen area.
The platen is set at a 45-degree angle and the top platen opens wide; allowing the operator to step inside the press for ergonomic and accurate parts placement.
The internal solid state RfsProtech 6KW Generator cures approximately 600 square inches of glue line per minute.
The Generator features solid state rectifiers and all aluminum cabinet for maximum conductivity and superior performance.
Two-hand no-tie-down safety controls for closing the top platen.
Controls are simple to understand, and are complete with the required push-buttons, switch, meters, digital operator display, and on-screen troubleshooting diagnostics.
The machine is controlled by a PLC for dependability and efficient maintenance. All controls will be provided for safe and efficient operation. The operator screen permits efficient operation, and the included press diagnostics screens assist in trouble-shooting when the need arises.
Proper interfaces will be provided for operational signals and emergency system stop.
All necessary RF controls, including buttons, meters, and PLC operator interface panel are mounted on a control panel attached to the left front of the press.
Interlocked top platen and safety switches on all access doors insure operator safety.
Power requirements are 480 volt, 60 cycle, 3 phase electric.
Circuit breaker protection is provided. A service disconnect is required for safety, but is not provided.
Powered In-Feed table with motor and controls
Out-feed steel deck
Voltage 480 volts 60 Hz
Pago y Devoluciones
- Forma de pago
- Transferencia/Deposito Bancario
Publicar mensaje
Ingresar to ask the seller a question.
AMXmachinery
PARTE: 12538 - CALDERA DE AGUA - LEFLAM - 521-050
PARTE: 12538 - CALDERA DE AGUA - LEFLAM - 521-050
MARCA: LEFLAM
MODELO: 521-050
CAP: 50000 KCAL/HR
PMT: 7 KG/CM2
INCLUYE EL QUEMADOR:
ECO FLAM GT-D1-MBC65DLE-RP15-40-120
MAX GAS 70 P TL HT
AMXmachinery
HORNO PARA CERAMICA, VIDRIO, METALES – 19 LITROS
PARTE:
2PG-FUSION7 - HORNO PARA CERAMICA, VIDRIO, METALES – 19 LITROSNUEVO CON GARANTIAThe digital Sentry Xpress 3 key controller comes standard on all Fusion-series kilns. Control both heating and cooling with simple 3-key operation.The Sentry Xpress 3-key controller is packed with features. It includes two modes: Single Speed and 8-segment Ramp-Hold.Features of the Sentry Xpress 3-key Controller on Non-Ceramic Paragon KilnsDesign programs with up to 8 segments (steps) in Ramp-Hold mode.Fire...
AMXmachinery
ENGOMADORA 36" - 72"
PARTE # 2CK-F-QSGA-08-36 - ENGOMADORA DE 36" ANCHO- IDEAL PARA LAS PEGADORAS DE SECCIONES DE 6 A 14 SECCIONES- FACIL OPERACION- PARA PEGAMENTOS BASADOS EN AGUA BLANCOS Y AMARILLOS- CUANDO SE PRESIONA EL PEDAL, SUBE LA MAYA CON EL PEGAMENTO Y SOLO APLICA LA CANTIDAD DE PEGAMENTO CORRECTA- CONSTRUIDA TOTALMENTE DE ACERO Y LAS PARTES CON CONTACTO CON EL PEGAMENTO ESTAN HECHAS DE ACERO INOXIDABLE- INLCUYE CUBIERTA PARA CONSERVAR EL PEGAMENTO FRESCO CUANDO NO SE USA LA MAQUINA- PLATO PERFORADO DE 8" ...
AMXmachinery
GUILLOTINA 8 PIES - ST JOE MACHINES
PARTE: 11756
- GUILLOTINA 8 PIES - ST JOE MACHINES
5 - GUILLOTINA. 8 PIES ST JOE MACHINES CON CUCHILLA DE 90” DE
LARGO ACCIONADA POR UNIDAD HIDRAULICA.