ID: 1919
Open
Description
PARTE: 2LI-D - MEDIDOR DE HUMEDAD PARA MADERA – SIN PINS - LIGNOMAT – LIGNO-SCANNER D
Nuevo con garantía
Measuring | 5-60% dependent upon species setting* |
Display | 0.1% resolution for the entire range. |
Species | 71 wood group settings, or simply use specific gravity of the wood, between 0.3 and 1.0 (setting 30-100) |
Gypsum | N/A |
Reference | 0-99 for non-wood building materials |
Calibration | Stable calibration not affected by ambient temperature. Calibration is internally checked and automatically adjusted if necessary. |
Calibration Check | External calibration check block #TS is available to verify the calibration and functions of meter. |
Included | Pouch, one 9V battery, manual and laminated wood group chart. |
Size | Pocket-size 2″ x 5.5″x0.5″, Measuring pad 1 5/8″ x 2 5/8″ |
Weight | 8 ounces (200g), made out of high-impact plastic |
Warranty | All moisture meters have a 2 year warranty. Pins and battery are excluded. |
The measuring depth of a pinless meter is crucial. Moisture readings are too low, when the Scanner is placed on a work piece which is thinner than the measuring depth. Scanners never measure any deeper than the measuring depth.
The entire measuring pad has to be on a flat and smooth surface for accurate readings
*Species Corrections for Ligno-Scanners and Ligno-VersaTec correlate directly to the Specific Gravity. Example: For a specific gravity of 0.57 (0.57g/cm 3 )set species # 57. Specific Gravity for most wood species can be found on the Internet. We also include a Species Chart with recommended settings.
The Ligno-Scanners SDM and the Ligno-VersaTec have calibrations built-in for drywall and concrete and a reference scale for non-wood building materials.
Measuring range: 5-60% dependent upon Species. For hardwoods the Scanners read lower than 5%, for softwoods the Scanners start reading above 5%. Resolution of read-out: 0.1% Less accurate above Fiber Saturation Point at 30%.
Wood temperature correction is not necessary.
1 9-V Battery for 3000 Readings, Battery included
Size: 1/2″H x 2″L x 5″W (for Scanner LD width is 2 7/8″) Weight: 8 ozs
Comes in a Carry Pouch with Belt Loop.
Payments & Returns
- Payment Methods
- PayPal
Postage & Shipping
- Item Location
- 31627, Chihuahua, Mexico
- Ships To
- Mexico
- Pick-ups
- No pick-ups
- Returns Accepted
- No
Post Message
Sign in to ask the seller a question.
AMXmachinery
EXTRACTOR DE TURBINA - MOTOR 1 HP - S&P
PARTE:
AMX-10048 - EXTRACTOR DE TURBINA - MOTOR 1 HP - S&P
USADO - MUY BUENAS CONDICIONES
MARCA S&P
MODEL: CSB-1300
MOTOR 1 HP, 127/220V, 1 FASE, 60 HZ
AMPS: 17.3 / 9.5
3535 RPM
VOL. 1300 M3/H
HECHO EN MEXICO
ENTRADA: 5-1/2” DIAMETRO
SALIDA RECTANGULAR: 5” ALTO X 4” ANCHO
MEDIDAS TOTALES: 46 CM ANCHO X 38 CM FONDO X 57 CM ALTO
-500x500.jpg)
AMXmachinery
CEPILLO 2 CARAS 16", 24"
PARTE # 3GO-GT-400B - CEPILLO 2 CARAS – CAPACIDAD 16" ANCHO – MOTOR 10, 7.5, 2, ½ 10 HPPARTE # 3GO-GT-610B - CEPILLO 2 CARAS – CAPACIDAD 24” ANCHO – MOTOR 15, 10, 2, ½ HPPARTE # 3GO-GT-610A - CEPILLO 2 CARAS – CAPACIDAD 24" ANCHO – MOTOR 20, 15, 3, ½ HPESPECIFICACIONESPARTE # 3GO-GT-400B - CEPILLO 2 CARAS – CAPACIDAD 16" ANCHO – MOTOR 10, 7.5, 2, ½ 10 HPMotor: 10hp,7.5hp,2hp,1/2hpMaximum width of cut: 405MM Minimum thickness of cut...
AMXmachinery
PARTE: 12352 – TRITURADORA - CARTON – CON TRANSPORTADOR – BLOAPCO
PARTE:
12352 – TRITURADORA - CARTON – CON TRANSPORTADOR – BLOAPCO
SIN
COMPACTADORA
USADO EN BUENAS CONDICIONESDESIGNED TO SHRED
CORRUGATED SHEETS AND BOXES, OVERSIZED FLAP CUTS AND DIE PRESS WASTE TO SMALL IRREGULAR PIECES...APPROXIMATELY 5" X 8" PIECES. BOTTOM DISCHARGE
OUTLET FEEDS SHREDDED MATERIALS INTO CHUTES BINS, COMPACTORS, OR PNEUMATIC
SCRAP HANDLING SYSTEMS. IT HAS THE CAPACITY TO HANDLE 300 POUNDS PER HOUR PER
HORSEPOWER WHEN HANDLING CORRUGATED BOARD MATERIALS.
AMXmachinery
CABEZAL LIJADOR
PARTE # 2SR-B12 – CABEZAL LIJADOR CON 1 SET DE CEPILLOS Y LIJA INSTALADONuevo con garantíaEl cabezal lijador remplaza el lijado a mano en las superficies con figura, lijando sin perder la figura original.Hecho de aluminioMedida cabezal: 5-1/4” ancho x 9” diámetro x 1” centro para flechaIncluye 15 cepillos 4” ancho y 1 set de lija instaladoLijas disponibles: grano 60, 80, 100, 120, 150, 180, 220